The Power Probe 4 Master Combo Kit combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit-testing capabilities. The Power Probe 4 provides simplified testing of Motors, Lights, Relays, and Sensors, and even Fuel Injectors. Also, like all Power Probe circuit-testers, it supplies Power and Ground for functional component testing on or off the vehicle. The PPECT3000 will help you trace short and open circuits quickly and accurately.
Features
PP4
– Supply power or ground for functional component testing
– Self-Resetting thermal 8 amp circuit breaker
– Multiple DC Volt readings on the same display
– Ohmmeter provide active feedback
– 12 – 24 Volt Range
– Bad ground indicator
– Continuity Tester
– Component Tester
– AC-RMS, AC Peak to Peak, Frequency and pulse width indicators are available for signal testing
– fuel injector for easy circuit diagnosis
– PCM/ECM Driver supplies safe voltage for testing computer driver circuits
– PPECT Mode for signal for detection of open circuits (When used with the ECT2000/ECT3000)
-Active LED lighting for illuminating workspace
– Power cable length of 23 Feet
ECT3000
Locate short circuits without removing plastic panels, moulding, and carpet Find short to ground circuits, switches, or breaks in wires Test and find intermittent conditions Sensitivity adjustment from 1-8 in (3-20 cm) Trace short to ground wires with visual navigation & sound indicators Works on Cars, Boats, RV’s, Light Duty, Heavy Duty Trucks, and Trailers.
| PP4 | |
| Min Operating Voltage | 8 VDC |
| Max Operating Voltage | 30 VDC |
| Max Tip Voltage | 450 Volts |
| Probe Tip Resistance to Ground | 130K Ohms |
| Computer Safe | 0.1mA floating tip |
| Voltage Measurement | -100 to 200 VDC / VAC |
| Voltage Resolution | -99.99 to 99.9 V – 0.01V(10mV)
100.0 to 199.9 V – 0.1V (100mV) |
| Glitch Capture | >380µS Min Pulse Width |
| Power Feed Test | < 30 mA |
| Resistance Measurement | Ohms to 10K Ohms |
| Frequency Measurement | 1Hz to 9999Hz |
| Driver Test | 50 Ohm Pull Up on Tip
Driver On Range: 50mV to 1V |
| ECT Signal Detection | 2 sec. |
| Fuel Injector Mode | LED Flash @ Min 35V @ 100µS Pulse |
| Red LED Response | Within 0.5V BATT V and < 10 Ohms |
| Green LED Response | < 10. Ohms |
| Circuit Breaker | 8 Amp Thermal – Auto Reset |
| Breaker Trip Response | 8 Amps = No Trip
10 Amps = 20 min. 15 Amps = 6 sec. 25 Amps = 2 sec. Short Circuit = 0.3 sec. |
| Operating Temperature | -20°C (-4°F) to 50°C (122°F) |
| Storage Temperature | -40°C (-40°F) to 65°C (149°F) |
|
ECT3000 |
|
| TRANSMITTER | |
| Min Operating Voltage | 6 VDC |
| Max Operating Voltage | 48 VDC |
| Working Current | <200mA |
| Working Frequency | 4KHz |
| Max Operating Temp | 50°C |
| Max Storage Temp | 70°C |
| Max Operating Relative humidity | 80% (Non-condensation) |
| Max Storage Relative humidity | 80% (Non-condensation) |
| Altitude | <2000m |
| RECEIVER | |
| Power Supply | 2 X 1.5V AAA |
| Working Current | When not signal be detected <15mA |
| Power Consumption When Power Off | <10uA |
| Max Operating Temp | 50°C |
| Max Storage Temp | 70°C |
| Max Operating Relative humidity | 80% (Non-condensation) |
| Max Storage Relative humidity | 80% (Non-condensation) |
| Altitude | <2000m |
Reviews
There are no reviews yet.